Share your CCNA Wireless Experience

Thanks Highlander, I got the path right for that new question because my answer was exactly as you posted.
Ill review your notes for Q103 since it was on the test
Q268 says “Only” (I still think it is 2 after research)

New Question 2
What is the 802.11b Channel Width.
I chose 20 Mhz, but review after it is 22 Mhz (b is 22 and a/g is 20)

New Question 3
Choose two ports for something (sorry)
A. 1645
B. 1646
C. 1812
D. 1813
E. 1845
F. 1846
This should be C and D I believe.

New Question 4
How to keep 802.11 rates and 128 bit encryption?
A. WPA-TKIP
B. WPA2-AES
C. CKIP
D. WEP
Should be B.

New Question 5
Which two modes support MFP?
Can’t remember the answers, but is should be:
For client it should be Local, HREAP, Bridge
For Infrastucture it should be local, monitor and maybe HREAP?
How can we narrow this to 2?

New Question 6
What is this picture
https://sc01.alicdn.com/kf/HTB1G6MtHpXXXXcuXXXXq6xXFXXXq/200667255/HTB1G6MtHpXXXXcuXXXXq6xXFXXXq.jpg

I remember the image, but not the answers, but I think it is a parabolic dish?

New Question 7 and 8
These were dBm and w conversions. Easy

I will post the 4 questions from the word document as well if we can find a answer to #5 and review these for now.

Sorry Question 4 is to keep “802.11n” rates

@Grad @Raticulin could you please send me updated dumps I have exam scheduled in a few days. Please. Thank you so much in advance. medkaloks06(@)gmail.com

After initial deployment at a customer site, the master controller mode function left enabled on the secondary controller after access points were primed and statically configured with primary, secondary, and tertiary controller failover. The access points reboot after a POWER failure. Which controller will the APs associate to when the reboot process is completed?
a. primary
b. secondary
c. tertiary
d. guest anchor

The answer is b, but I don’t get it why…1 step is to broadcast on LAN…and I guess Master WLC replies to that if it’s on the same LAN.subnet or ip-helper is configured on a switch to redirect UDP 524 to specific WLC ip address….but nothing is said about that.

So, if the first step fails, move to step 2, which is preconfigured ips of WLCs…question, does AP loses its config due to a power outage?

@Z
Should be A, primary. The Master Controller is used if there is no primary, secondary, or tertiary controller assigned to an AP.

“When there is a master controller enabled, all newly added access points with no primary, secondary, or tertiary controllers assigned associate with the master controller on the same subnet. This allows the operator to verify the access point configuration and assign primary, secondary, and tertiary controllers to the access point using the All APs > Details page.
The master controller is normally used only when adding new access points to the Cisco Wireless LAN solution. When no more access points are being added to the network, Cisco WLAN solution recommends that you disable the master controller.”

https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69561-wlc-faq.html

@Highlander @Grad @ Foxx can anyone kindly send me recent questions. Please. I don’t have the 70q yet and any subsequent questions. Thanks you so much in advance. All of you. Cheers

Shadow the latest one I have is the 437Q and the link is a few pages back.

Ok Grad so should i go ahead and assume that’s the latest one, reason why i am asking is because I heard some mention of 70q. So i just wanted to make sure am on the same page with everyone. Could anyone else verify this and update me with the file via email. Please please. Thanks in advance.

Q277 from 437q dump

What three components are required to configure Mobility Group Member between Wireless LAN Controllers? (Choose three.)

A. Controller Management IP Address
B. Controller Virtual IP Address
C. Controller Multicast IP Address
D. Controller MAC Address
E. Controller Mobility Group Name
F. Controller AP Management IP Address
G. Controller RF Group Name

Answer: ADE

Someone please tell me this is wrong

@grad Thanks for sharing your experience, you gave me hope to pass the exam.
About the new questions:
New Question 3
is asking about the ports of radius authentication, the answer is:
A. 1645
C. 1812

New Question 4

It’s OK . WPA2-PSK and WPA2-Enterprise both use 128 bit keys (TK1 & TK2) for the data encryption.

I hope you post the 4 question from word document

regard

@Raticulin has u sat ur exam already. If yes please share ur exeprience.

Thanks

@Shadow
Q277’s answer is correct.

In order to add Mobility Group members in the WLC, you go to Controller, Mobility Management, Mobility Groups, Add. You have to provide:

controller IP address (this would be the management address)
controller MAC
mobility group name
hash (if used)

So what about the Virtual IP ??

@shadow
I do not think you know anything, I don’t did the exam. If you do not know what the virtual IP , I advise you not to take the exam and study more.

That’s set in Controller, Interfaces, Virtual. There is only one virtual IP set on the controller. There wouldn’t be a need to set the same virtual IP everytime you added members.

Hey guys I mistook this question for Q55.

New Question 5
Which two modes support MFP?

I find that in la official web cisco, but they say that are three modes Local,monitor and Flexconnect sometimes.

Lightweight access points support infrastructure MFP in local and monitor modes and in FlexConnect mode when the access point is connected to a controller. They support client MFP in local, FlexConnect, and bridge modes.

https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010110100.html

From Word Document on Test:
Q1
How to configure in iphone a hidden SSID?
A1
Settings->Wifi->Other->SSID name and security

Q2
8. Which are requirements of real time apps?
A. low latency
B. Low jitter
C. Voice
D. …
E. …
A2
A and B

Q3
You need to send all guest traffic to the DMZ, this needs to be setup so that no matter what AP the guest connects to it will get sent here, how would you set this tunnel
A. symmetrical tunnel
B. mobility-anchoring
C. asymmetrical tunnel
A3
B

Q4
11. Which AP modes accept client connections? (Choose three)
A. Local
B. Monitor
C. Flexconnect
D. Roque Detector
E. Sniffer
F. Bridge
G. SE-Connect
A4
ACF

Let me know if I answered these wrong. Good luck all

I think answers are correct

@Raticulin
New Question 3
Choose two ports for something (sorry)
A. 1645
B. 1646
C. 1812
D. 1813
E. 1845
F. 1846
A: 1812 and 1645 for Radius Authentication messages
A: 1813 and 1645 for Radius Accounting messages
A: 1812 and 1813 for new ports
A: 1645 and 1646 for old ports

From 437q
16 65 68 91 93 95 99 100 103 106 108 111 112 119 121 199 207 216 223 227 228 232 265 268 269 270 276 279 285 288 319 328 340 341 346 347 351 382 409 410 413 414 418 419 422 424 425 426 429 430 431

@Grad Thank you so much you are a good people .
I don´t know if you 437 are same order than me , for you the questinon 16 is ?

QUESTION 16
Which four options are the characteristics of the original 802.11 protocol? (Choose four.)
A. Defined DSSS and FHSS as possiblemethods for modulation
B. Designed to operate in the 5 GHz ISM frequency spectrum
C. The most common deployment is three non-overlapping channels that are 20 MHz wide
D. The protocol sets the maximumthroughput at 1 Mb/s or 2 Mb/s
E. Defined FHSS and OFDM aspossible methods for modulation
F. The most common deployment is three non-overlapping channels that are 22 MHz wide
G. Designed to operate in the2.4 GHz ISM frequency spectrum
H. The protocol sets the maximum throughput at1 Mb/s
Correct Answer: ACDG
Section: (none)
Explanation

No Q16 on mine is:
QUESTION 16
Microsoft Active Directory integrated machines are not authenticating to the internal WLAN.
The WLAN settings are WPA2-AES-802.1x and are authenticating to a Cisco Identity Services
Engine server. You investigate and note that non-domain authenticated machines are properly
authenticating to the WLAN using their Active Directory credentials.
Why would this problem occur?
A. The WLAN is configured improperly in group policy.
B. The ACS server is not joined to the domain, causing authentications to fail.
C. The domain machines are configured to disable the wireless adapter.
D. The non-domain machines are using local accounts that are not authenticated through the domain.
Answer: A

Look a few pages back for my link to the 437q

Sorry typo above:

New Question 3
Choose two ports for something (sorry)
A. 1645
B. 1646
C. 1812
D. 1813
E. 1845
F. 1846
A: 1812 and 1645 for Radius Authentication messages
A: 1813 and 1646 for Radius Accounting messages
A: 1812 and 1813 for new ports
A: 1645 and 1646 for old ports

Hi guys,
I did my test today and I got it! 89x/1000. As soon I get sometime I’ll post few questions that I saw today.

By the way…I saw that question above, about the RADIUS ports.
CiscoMan

That great CiscoMan, I am taking this again in a few days, any help would be appreciated as I do not plan on failing a 2nd time.

When using multiple SSIDs on a lightweight AP, how does the traffic of each SSID reach
the 802.3 network?

A. provide routing between them at the core so that the SSIDs can reach the internet
B. configure 802.11q trunking on the Ethernet switch port that is connected to the AP
C. configure ACLs at the switch port that will allow all desired SSIDs to pass traffic
D. configure the SSIDs on the WLC and it will regulate the traffic based on traffic type
Ans B I dont think so

@Prof would you like to elaborate why you don’t think B is correct. And what’s would be your choice.

Trunk is not needed for lightweight AP, Capwap tunnel is created on acces port and can cary traffic from multiple VLAN

For latest and updated dumps
http://www.dumpsforsure.com/cisco.html

Anyone has the VCE format for 437q dump please share. Thanks

@Grad @Prof @CiscoMan @Raticulin

Please i need VCE for the dump

Go find something to do Anonymous. If you can’t share dump freely then you should be ashamed of yourself.

Passed today beyond 97X :-/ but it s ok :-)

So see you in CCNP guys ! Good luck !

@Highlander

Could you please share ur experience. Also I would like to know if any simulation was part ur exam and those many questions about WCS.

Thanks

No Lab, no sim, no wcs

about 1/3 of the question are not in 437Q but they are simple if you did practice.

Do you by any chance recall any of the 1/3 questions.

no i forgot already, because they were too simple, I finished the 65 questions in 20 mins. sorry.

Hi guys,
This is the list of questions I saw on test according to the PL 437
8, 14, 16, 24, 29, 52, 55, 68, 84, 91, 93, 95, 99, 100, 108, 111, 112, 119, 121, 139, 147, 193, 199, 207, 209, 210, 212, 213, 216, 219, 223, 232, 238, 268 (PCF), 277, 279, 288, 319, 344, 351, 356, 360, 380, 382 (is incomplete on PL) and 410.
No lab, no WCS, one Prime question, 1 question about the data traffic flow between 2 APs.

By the way…congrats @Highlander, well done!

Good luck,
CiscoMan

Thanks CiscoMan.

Do you remember that ask in the question about chose 2 port what said Grad?

An engineer has been asked to disable all OFDM rates in the wireless environment. What three rates should be disabled to fulfill these requirements (choose three)
2
5.5
11

Why? This arent OFDM rates, OFDM are: 6,9,12,18 which are other options in question???

@prof, the answer to this question is wrong, the question itself is wrong…we have already talked about it in this thread, look back and you will see….

@CiscoMan: thank you very much :-)

Hello friend , this question is a classic but nobody know what is the answer , please they did the exam know what is the answer because it should be A,B,E and H .Help me please

QUESTION 187
Which three items are allowed on an Ethernet trunk port? (Choose three.)
A. autonomous AP
B. FlexConnect AP
C. local AP
D. monitor AP
E. rogue detector AP
F. sniffer AP
G. SE-Connect AP
H. Cisco WLC
Correct Answer: ABE

Could someone point me in the right direction where I can find the questions from the word document. Thanks

HI guys , anyone took exam recently? please share your experiance and if you have any new dump please share it

QUESTION 187

Which three items are allowed on an Ethernet trunk port? (Choose three.)

A. autonomous AP
B. FlexConnect AP
C. local AP
D. monitor AP
E. rogue detector AP
F. sniffer AP
G. SE-Connect AP
H. Cisco WLC

Correct Answer: ABE

Yes this is correct ABE…. H is wrong.

Of course a WLC could and in reality should be on a trunk port.

But this is not the question. you have been presented with OPERATING MODES of an WLC. Response H ist not a WLC mode. A WLC mode does not exist. WLC ist the controller itself. The question is, which wlc mode can operate on a trunk port?

hope it helps.

When using multiple SSIDs on a lightweight AP, how does the traffic of each SSID reach
the 802.3 network?

A. provide routing between them at the core so that the SSIDs can reach the internet
B. configure 802.11q trunking on the Ethernet switch port that is connected to the AP
C. configure ACLs at the switch port that will allow all desired SSIDs to pass traffic
D. configure the SSIDs on the WLC and it will regulate the traffic based on traffic type

This question is not in the exam and it is ambiguous anyway.

Because you can have many SSID that ends in the same VLAN. You also can have for each SSID a dedicated VLAN. The AP itself has nothing to do with this, because in a standard design, the traffic will end at the controller and he will do the tagging job.

BUT you could have another type of design, split mac architecture for example, known as flexconnect. In this scenario, the wireless traffic could be dropped at the port where the AP is connected to the switch, and then it will take its way like any other traffic to the HQ or else.

It is not clear in the question, what is wanted here.

Passed!!

Congratulation !

Now come to ccnp and you will see, we have a problem there ! :-)

@Shadow and @Highlander which materials do you recommend to someone preparing for this exam

I had videos from

1. Keith Barker (cbtnugets)
2. Jerome Henry (cisco)

but you will also need to practice to understand. So you will need a Lab, a virtual one.