Share your WIFUND Experience

Passed too using it Natasha

Hey guys, I can’t advice anybody to write the exam now, I write my own today I fail it, my score 830, like 40 new questions are there

I will try to share some new questions dat i can still remember

Passed too using Maria’s dumps

I passed not using any of the crap people are trying to sell. The OCG is your friend and you can find PDFs for free online.

Dumps should be used to study but not to memorize in hopes you get the exact questions. If you get an answer wrong in the dump look it up in the OCG and find out why it was wrong.

Hello,

The dump if they serve you, but you should also know more things (EoIP, CAPWAP states), come 2 drog and drop, today pass, good luck to all

Passed too using it Latila
Thanks so much
Score : 985
Time spent : 40 min

The above post is nearly identical to one on the WIDESIGN 300-360 forum. In other words scam

What three components are required to configure Mobility Group Members between Wireless LAN
Controllers? (Choose three.)
A. Controller Management IP Address
B. Controller Virtual IP Address
C. Controller Multicast IP Address
D. Controller MAC Address
E. Controller Mobility Group Name
F. Controller AP Management IP Address
G. Controller RF Group Name
Correct Answer: ADE

QUESTION 3
A wireless engineer is designing the wireless networking for a company with offices in two different locations.
Which two regulatory bodies should they check to find the maximum EIRP allowed? (Choose two.)
A. IEEE
B. FCC
C. ITU-R
D. ETSI
E. Wi-Fi Alliance
Correct Answer: BD
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

QUESTION 3
A wireless engineer is designing the wireless networking for a company with offices in two different locations.
Which two regulatory bodies should they check to find the maximum EIRP allowed? (Choose two.)
A. IEEE
B. FCC
C. ITU-R
D. ETSI
E. Wi-Fi Alliance
Correct Answer: BD

Explanation/Reference:
Explanation/Reference:
Explanation:

QUESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

Passed using Maria’s dumps

Passed also by using the dumps posted above by Maria on the comment above
Thanks God

QUESTION 473
An engineer has been asked to disable all OFDM rates in the wireless environment. What three rates should
be disabled to fulfill this requirement? (Choose three.)
A. 2
B. 5.5
C. 6
D. 9
E. 11
F. 12
G. 18

answer: c,d,f

But why not G?

Disregard all the previous posts saying they passed with a score and a link. They are scammers. I passed not too long ago and here is my experience.

-Roughly 10 questions right off the dump. Dump is still helpful for understanding topics but DO NOT plan to memorize and pass lol
-Not a single question about modulation types for me but perhaps just my luck of the draw.
-No WCS questions, just ISE and Prime. Very few questions on Prime or ISE but again perhaps just my luck.
-Also used CBT Nuggets videos, Jerome Henry videos (safari books trial), flash cards I found online (search for neckercube blog) and the OCG.
=====================================
Questions I remember:

SSID’s case sensitive? Yes.

Which are not examples of real-time applications… email, social media, video, voice. I chose email + social media

What is a third party application for for analyzing traffic – I chose wireshark?

Antenna radiation pattern… mine was Yagi I believe.

Cisco recommended switchport config for AP in local mode with multiple SSIDs – I picked trunk but in reality once access vlan will work

AP on different vlan needs to find controller, add to config on svi udp forward 5246 + ip helper of mgmt address.

Multi choice question with some possible answers involving mbssid, I chose one of these.

Multi choice question about secure webmode on WLC CLI not using SHH – I chose ‘config network secureweb cipher-option high enable’ as one answer.

Question with diagram of WPA settings, client cannot connect at 802.11n speeds how to fix? Answer is ‘open’ and ‘wpa2+AES’

Thank you Eva
The Vce Test simulator is awesome

Does anyone have the dumps for the exam
And why is this page filled with so many spammers
I need the dumps please if anyone can hep

I want to request image wlc

Hello Team
Can anyone share with me the latest CCNA Wireless DUMP please? ekiams7 @ gmail com

Thaaaaaaaanks Sophia
I passed today using your dumps
I can confirm that they still valid
Thank you for your help and for everything !!

Hey there, I have been reading the forum to find out more info and prepare the exam (which I passed at the end of August 2018). To be honest, I studied from the Official Guide for few months and I work with Cisco gears…however, we know how Cisco exams work….Not always questions are clear/entirely correct.

After preparing the various topics on the official guide, I have used Prepaway to refine and make sure to be fully prepared, testing my knowledge. The file is correct and worked perfectly (bear in mind queries are are constantly updated).

You can use the following Promo code to get 45% discount: NE214463.

Feel free to use it even for other products.
Cheers
M.A.

Some good info posted by ipassed, franledo and elisa

The company I work for bought the Cisco on demand learning though Global Knowledge for the WiFUND 200-355 exam. Can anyone weigh in how relevant this course is to the actual exam. There’s a boat load on info to absorb and it almost feels liked a Cisco marketing pitch in alot of the modules. I’ve got a little over a month to get this nailed down. I’m drowning at the moment lol. Any pointers or tips?

Hi Clax, I have gone through Official GUide and some material from different sources…In reality, I do not think there is anything (apart from certain dumps) that can fully prepare you to the exam. Course, guide etc help you though on your daily work to “connect the dots”. Of course, many info are not up to date. If you think, Cisco DNA out there today, i think it’s not even mentioned in the exam.
Luckily Cisco removed the WCS queries which were way outdated!

Prime is barely touched in the exam…If you need to pass, I would advise to work on the Course and material you got, and test your knowledge before hand.

I used Prepaway and if you want you can use this code to get a nice discount: NE214463
With the PDF you got access also to videos and tutorial that surely helped me for the preparation.

Cheers

.QS

Hello All,

I need a valid dump for CCNA Wireless 200-355 and send it to my mail on {email not allowed}…

Thanks in advance :)

Thanks Ivy
I passed today too
I can confirm that this dumps is valid 95% and stable
Thanks God
Do you have ccnp route dumps ??

Awesome dumps
Thank you Ivy

QUESTION 3
A wireless engineer is designing the wireless networking for a company with offices in two different locations.
Which two regulatory bodies should they check to find the maximum EIRP allowed? (Choose two.)
A. IEEE
B. FCC
C. ITU-R
D. ETSI
E. Wi-Fi Alliance
Correct Answer: BD

Explanation/Reference:
Explanation/Reference:
Explanation:

QUESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
——————————————————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————

D. ETSI
E. Wi-Fi Alliance
Correct Answer: BD

Explanation/Reference:
Explanation/Reference:
Explanation:

QUESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
——————————————————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?

QUESTION 15
A help desk ticket states that a wireless access point has not joined its controller and is flashing rapidly. How
can the help desk administer the access point with the default settings?
A. console
B. SSH
C. Telnet
D. HTTP
E. HTTPS
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 16
After you configure the Cisco 5508 Wireless Controller v7.6, a customer requests an SSID that allows for client
web authentication with email input. Which authentication method should be used?
A. pass-through
B. authentication
C. splash page web redirect
D. conditional web redirect
E. on MAC filter failure
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 17
Which two principles must be considered when deploying a wireless network through a wooded area?
(Choose two.)
A. absorption
B. reflection
C. diffraction
D. scattering
E. refraction
Correct Answer: AD
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 18
What is an interferer that an engineer may see in Cisco CleanAir?
A. microwave ovens
B. rogue APs
C. malicious clients
D. co-channel interference
Correct Answer: A

QUESTION 15
A help desk ticket states that a wireless access point has not joined its controllesar and is flashing rapidly. How
can the help desk administer the access point with the default settings?
A. console
B. SSH
C. Telnet
D. HTTP
E. HTTPS
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 16
After you configure the Cisco 5508 Wireless Controller v7.6, a customer requests an SSID that allows for client
web authentication with email input. Which authentication method should be used?
A. pass-thscrough
B. authentication
C. splash page web redirect
D. conditional web redirect
E. on MAC filter failure
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 17
Which two principles must be considered when deploying a wireless network through a wooded area?
(Choose two.)
A. absorption
B. reflection
C. dicsffraction
D. scattering
E. refraction
Correct Answer: AD
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 18
What is an ainterferer that an engineer may see in Cisco CleanAir?
A. microwave ovens
B. rogue APs
C. malicious clients
D. co-channel interference

Just wondering how this site would look like when there were no spammers on this site.. Are there any real ccna wireless students left here?

Is there a premium access for Wireless TUT like there is for 9TuT? I’m studying for the 200-355 and need more help like what 9TuT did for me on ICND-1…

QUESTION 379
You are configuring SNMPv1/v2c on a WLC. What should you do for improved security?
A. Remove the default SNMPv1 community.
B. Remove the default SNMPv1 and SNMPv2 communities.
C. Remove the default SNMPv2 community.
D. Remove the default SNMPv3 users.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
The controller has commonly known default values of “public” and “private” for the read-only and read-write
SNMP community strings. Using these standard values presents a security risk. If you use the default
community names, and since these are known, the community names could be used to communicate to the
controller using SNMP. Therefore, we strongly advise that you change these values.
Step 1
Choose Management and then Communities under SNMP. The SNMP v1 / v2c Community page appears.
Step 2
If “public” or “private” appears in the Community Name column, hover your cursor over the blue drop-down
arrow for the desired community and choose Remove to delete this community.
Step 3
Click New to create a new community. The SNMP v1 / v2c Community > New page appears.
Step 4
In the Community Name text box, enter a unique name containing up to 16 alphanumeric characters. Do not
enter “public” or “private.”
Step 5
In the next two text boxes, enter the IPv4/IPv6 address and IP Mask/Prefix Length from which this device
accepts SNMP packets with the associated community and the IP mask.
Step 6
Choose Read Only or Read/Write from the Access Mode drop-down list to specify the access level for this
community.
Step 7
Choose Enable or Disable from the Status drop-down list to specify the status of this community.
Step 8
Click Apply to commit your changes.
Step 9
Click Save Configuration to save your settings.
Step 10
Repeat this procedure if a “public” or “private” community still appears on the SNMP v1 / v2c Community page.
QUESTION 380
Which spread spectrum technique uses 11-bit chips to transmit 1 bit of data over a 22-MHz channel?
A. DSSS
B. FHSS
C. OFDM
D. MIMO
E. CCK
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
For every 0 or 1 you want to send, DSSS generates a code representing that 0 or that 1. This code, also called
symbol or chip, can be a sequence of up to 11 bits (this is called the Barker 11 code), and these 11 bits are
sent in parallel over the 22 MHz channel. You can lose up to nine of these 11 bits due to interferences and still
understand whether the code sent was supposed to represent a 0 or a 1.
QUESTION 381
The network administrator has used VLANs to separate VoIP frames from data frames in the wired network.
What must the administrator use to separate those frames in the wireless network?
A. multiple SSIDs
B. multiple authentications
C. multiple WEP or WPA keys
D. multiple channels
E. multiple 802.11 radios (a, b, g, n)
Correct Answer: A

QUESTION 392
Which method is used to shield the client from class 3 management attacks?
A. client MFP
B. WEP
C. WPA
D. client protection suite
E. 802.1X
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
With MFP, all management frames are cryptographically hashed to create a Message Integrity Check (MIC).
The MIC is added to the end of the frame (before the Frame Check Sequence (FCS)).
When MFP is enabled on one or more WLANs configured in the WLC, the WLC sends a unique key to each
radio on each registered AP. Management frames are sent by the AP over the MFP-enabled WLANs. These
APs are labeled with a frame protection MIC IE. Any attempt to alter the frame invalidates the message, which
causes the receiving AP that is configured to detect MFP frames to report the discrepancy to the WLAN
controller.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/82196-mfp.html
QUESTION 393
Which protocol helps the administrator to determine whether a detected rogue AP is in the network of the
organization?
A. RLDP
B. RCP
C. RDP
D. RAPP
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
RLDP is an active approach, which is used when rogue AP has no authentication (Open Authentication)
configured. This mode, which is disabled by default, instructs an active AP to move to the rogue channel and
connect to the rogue as a client. During this time, the active AP sends deauthentication messages to all
connected clients and then shuts down the radio interface. Then, it will associate to the rogue AP as a client.
The AP then tries to obtain an IP address from the rogue AP and forwards a User Datagram Protocol (UDP)
packet (port 6352) that contains the local AP and rogue connection information to the controller through the
rogue AP. If the controller receives this packet, the alarm is set to notify the network administrator that a rogue
AP was discovered on the wired network with the RLDP feature. https://supportforums.cisco.com/
discussion/10941011/rd-rogue-detector-or-rldp-rogue-location-discovery- protocol
QUESTION 394
Which wireless client attempts to authenticate by using 802.1X?
A. supplicant
B. authenticator
C. EAP
D. RADIUS
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
802.1x is an Institute of Electrical and Electronics Engineers (IEEE) standard that provides an authentication
framework for WLANs. 802.1x uses the Extensible Authentication Protocol (EAP) to exchange messages
during the authentication process. The authentication protocols that operate inside the 802.1x framework that
are suitable for wireless networks include EAP-Transport Layer Security (EAP-TLS), Protected EAP (PEAP),
and EAP-Tunneled TLS (EAP-TTLS). These protocols allow the network to authenticate the client while also
allowing the client to authenticate the network.
802.1x authentication consists of three components:
http://www.arubanetworks.com/techdocs/ArubaOS_60/UserGuide/802.1x.php
QUESTION 395
Which EAP protocol requires a certificate only on the server side?
A. EAP-PEAP
B. EAP-FAST
C. EAP-TLS
D. EAP-SSL
Correct Answer: A

QUESTION 400
To implement a more secure means of communication for voice and data, what technology successfully resists
interference by utilizing a wider bandwidth than needed for the transmitting signal?
A. Spread Spectrum
B. Microwave
C. Extended U-NII2
D. ISM Bands
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 401
An 802.11g network is experiencing intermittent signal degradation and Spectrum Analyzer is being used to try
and locate the problem. What two interferers would likely be identified? (Choose two.)
A. multiple cell phones
B. microwave oven
C. FM Radio
D. cordless phone
E. document scanner
Correct Answer: BD
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
QUESTION 402
A wireless bridge is being installed near an airport. An organization informs the city council about complying
with max power levels that could be used and settings on any 5GHz channels used that might interfere with
the airport radar. What organization is this?
A. Institute of Electrical and Electronics Engineers
B. Internet Engineering Task Force
C. Federal Communications Commission
D. Wireless Fidelity Alliance
Correct Answer: C

QUESTION 379
You are configuring SNMPv1/v2c on a WLC. What should you do for improved security?
A. Remove the default SNMPv1 community.
B. Remove the default SNMPv1 and SNMPv2 communities.
C. Remove the default SNMPv2 community.
D. Remove the default SNMPv3 users.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
The controller has commonly known default values of “public” and “private” for the read-only and read-write
SNMP community strings. Using these standard values presents a security risk. If you use the default
community names, and since these are known, the community names could be used to communicate to the
controller using SNMP. Therefore, we strongly advise that you change these values.
Step 1
Choose Management and then Communities under SNMP. The SNMP v1 / v2c Community page appears.
Step 2
If “public” or “private” appears in the Community Name column, hover your cursor over the blue drop-down
arrow for the desired community and choose Remove to delete this community.
Step 3
Click New to create a new community. The SNMP v1 / v2c Community > New page appears.
Step 4
In the Community Name text box, enter a unique name containing up to 16 alphanumeric characters. Do not
enter “public” or “private.”
Step 5
In the next two text boxes, enter the IPv4/IPv6 address and IP Mask/Prefix Length from which this device
accepts SNMP packets with the associated community and the IP mask.
Step 6
Choose Read Only or Read/Write from the Access Mode drop-down list to specify the access level for this
community.
Step 7
Choose Enable or Disable from the Status drop-down list to specify the status of this community.
Step 8
Click Apply to commit your changes.
Step 9
Click Save Configuration to save your settings.
Step 10
Repeat this procedure if a “public” or “private” community still appears on the SNMP v1 / v2c Community page.
QUESTION 380
Which spread spectrum technique uses 11-bit chips to transmit 1 bit of data over a 22-MHz channel?
A. DSSS
B. FHSS
C. OFDM
D. MIMO
E. CCK
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
For every 0 or 1 you want to send, DSSS generates a code representing that 0 or that 1. This code, also called
symbol or chip, can be a sequence of up to 11 bits (this is called the Barker 11 code), and these 11 bits are
sent in parallel over the 22 MHz channel. You can lose up to nine of these 11 bits due to interferences and still
understand whether the code sent was supposed to represent a 0 or a 1.
QUESTION 381
The network administrator has used VLANs to separate VoIP frames from data frames in the wired network.
What must the administrator use to separate those frames in the wireless network?
A. multiple SSIDs
B. multiple authentications
C. multiple WEP or WPA keys
D. multiple channels
E. multiple 802.11 radios (a, b, g, n)
Correct Answer: Aa

QUESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the dswhole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
——————————————————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anscyxcone remember this option as well?
– ??? <<<can anyone remember this option as well?
UESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anycsone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
———————————sc———————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/csTACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyxcone remember this option as well?
– ??? <<<can anyone remember this option as well?
UESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority sca– determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption csof the whole header
– Separating the AAA func

https://www.youtube.com/watch?v=EyzpSSvUe2g

AlSalam Oulukm brother Romy, could you please send me the last dump, my email is {email not allowed}.

After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the dswhole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
——————————————————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packexats to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anscyxcone remember this option as well?
– ??? <<<can anyone remember this option as well?
UESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determsines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone rxemember this option as well?
– ??? <<<can anycsone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authenticaaxtion with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
———————————sc———————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtuascl MAC addresses.
– AVF – forwards packewdts to virtual MAC.
– Gateway Priority – detersmines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/csTACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyxcone remember this option as well?
– ??? <<<can anyone remember this option as well?
UESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 wdseconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority sca– determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining tdhe AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remeaamber this option as well?
TACACS+
– Encryption csof the whole headerb

KA

A controller is connected to a Cisco Catalyst switch. The switch port configuration looks like
this:

interface GigabitEthernet 1/0/10

switchport

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 1,20,30,50

switchport trunk native vlan 20

switchport mode trunk

Which controller CLI command assigns its management interface to the native VLAN
interface of the Cisco Catalyst switch?
A. config interface vlan management 0
B. config interface vlan management 50
C. config interface vlan management 1
D. config interface vlan management 20
E. config interface vlan management 30

The dump says A but why is it not D?

Can anyone share with me the latest CCNA Wireless DUMP please? ekiams7 @ gmail .com

ESTION 4
After installing a Cisco 5508 Wireless Controller using the default settings, how often will the RRM update
occur?
A. 30 seconds
B. 60 seconds
C. 300 seconds
D. 600 seconds
E. 3600 seconds
F. 7200 seconds
Correct Answer: D

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority sca– determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption csof the whole headec

Gents,
I’m going to take this exam at the end of the month. I’ve been using the following to study:
– Implementing Cisco Wireless Network Fundamentals (WIFUND) 1.0 (the online course)
– 200-355 OCG and the practice questions CD that comes with it.
– CCNA Wireless 200-355 Complete Video Course, Jerome Henry (PearsonVue)
– An actual 2504 WLC, a Cisco AIR-LAP 1142 Aironet AP, a Cisco AIR-CAP 2602 Aironet AP.
– A Windows 2012 server to setup a RADIUS service using Windows NPS.
– A Cisco 2650 PoE enabled Catalyst Switch.

I’ve noticed that the online course and the OCG is now starting to mention ISE and Cisco Prime. However, the dumps here show Cisco WCS questions are still being asked, but there’s no mention of WCS in any course material I’ve covered. Has anyone taken the exam recently? Can someone tell me if there are still WCS questions?

Content Review Question
Which three statements correctly describe site profiles and maps? (Choose three)
• Used to determine RF coverage
• Allow pan and zoom features
• Accessed through the Cisco ISE interface
• Can be created hierarchically: campus, buildings, floors
• Can be created hierarchically: location, landscape, layout

The correct answers are “Used to determine RF coverage”,”Allow pan and zoom features” and “Can be created hierarchically: campus, buildings, floors.”

Content Review Question
Which three features correctly describe the RF Prediction Tool? (Choose three)
• Allows you to import floor plans from third party tools
• Allows you to manage AP configurations and features
• Allows you to manage AP placement
• Helps create a bill of materials for new wireless equipment purchases
• Allows you to manage WLC placement

The correct answers are “allows you to import floor plans from third party tools”, “allows you to manage AP placement” and “helps create a bill of materials for new wireless equipment purchases.”

Content Review Question
Which three items are displayed in the search results of a discovered client in Cisco Prime Infrastructure? (Choose three.)
• MAC address
• VLAN ID
• Version of IP running
• OS version
• 802.11 protocol

The correct answers are “MAC address”, “Version of IP running” and “802.11 protocol.”

Content Review Question
Which three options are actions that can be taken on an alarm within Cisco Prime Infrastructure? (Choose three.)
• Assign
• Classify
• Annotate
• Notify
• Ignore

The correct answers are “Assign”, “Annotate” and “Notify”.

Hello Lillian, could you please send by email: nag.fawzi at gmail , thank u

Guys, where can we find out latest dump? I went through comments, but could not find any link.